Laser fabrication of composite layers from biopolymers with branched 3D networks of single-walled carbon nanotubes for cardiovascular implants
|
15.03.2021 |
Gerasimenko A.Y.
Kurilova U.E.
Savelyev M.S.
Murashko D.T.
Glukhova O.E.
|
Composite Structures |
10.1016/j.compstruct.2020.113517 |
0 |
Ссылка
© 2020 Elsevier Ltd A laser technology has been developed for fabricating structures from composite layers based on biopolymers: albumin, collagen, and chitosan with single-walled carbon nanotubes (SWCNT). The structures are intended for cardiovascular devices and tissue-engineered implants. This is evidenced by the results of studies. The composite layers were fabricated due to the phase transition of biopolymers and SWCNT aqueous dispersion under the influence of laser pulses. At the same time branched 3D networks of SWCNT were formed in the biopolymer matrix. The threshold energy fluence of laser pulses was determined (0.032–0.083 J/cm2) at which a bimodal distribution of pores was observed. The calculation of contact resistances between nanotubes at percolation units of 3D networks (20–100 kOhm) was carried out. Composite layers fabricated by laser demonstrated conductivity values that were higher (12.4 S/m) than those for layers by thermostat (4.7 S/m). The maximum hardness of the composite layers with SWCNT (0.01 wt%) by laser was 482 ± 10, 425 ± 10, and 407 ± 15 MPa for albumin, collagen and chitosan, respectively. The hardness of the thermostat layers was less than 100 MPa. The viability of endothelial cells in composite layers was improved. The composite layers ensured a normal level of hemolysis during interaction with erythrocytes.
Читать
тезис
|
Spectral analysis combined with nonlinear optical measurement of laser printed biopolymer composites comprising chitosan/SWCNT
|
01.06.2020 |
Savelyev M.S.
Gerasimenko A.Y.
Vasilevsky P.N.
Fedorova Y.O.
Groth T.
Ten G.N.
Telyshev D.V.
|
Analytical Biochemistry |
10.1016/j.ab.2020.113710 |
0 |
Ссылка
© 2020 Elsevier Inc. Biopolymer composites based on two types of chitosan (chitosan succinate and low-molecular weight chitosan) with single-walled carbon nanotubes (SWCNT) were created by laser printing. SWCNT have good dispersibility in chitosan solutions and therefore, can form relatively homogeneous films that was shown in scanning electron microscopy images. For the studies film composites were formed under the action of laser radiation on aqueous dispersion media. Study of the nonlinear optical process during the interaction of laser radiation with a disperse media has shown that low-molecular chitosan has a large nonlinear absorption coefficient of 17 cm/GW, while the addition of SWCNT lead to a significant increase up to 902 cm/GW. The threshold intensity for these samples was 5.5 MW/cm2 with nanotubes. If intensity exceeds the threshold value, nonlinear effects occur, which, in turn, lead to the transformation of a liquid into a solid phase. Characterization of films by FTIR and Raman spectroscopy indicated arising molecular interactions between chitosan and SWCNT detected as a small frequency shift and a change in the shape of radial breathing mode (RBM). The results indicate the possibility using aqueous dispersion media based on chitosan and SWCNT to create three-dimensional films and scaffolds for tissue engineering by laser printing.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy
|
15.02.2020 |
Gerasimenko A.
Ten G.
Ryabkin D.
Shcherbakova N.
Morozova E.
Ichkitidze L.
|
Spectrochimica Acta - Part A: Molecular and Biomolecular Spectroscopy |
10.1016/j.saa.2019.117682 |
0 |
Ссылка
© 2019 Elsevier B.V. The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.
Читать
тезис
|
Nano-liquid chromatography for enantiomers separation of baclofen by using vancomycin silica stationary phase
|
08.11.2019 |
D'Orazio G.
Fanali C.
Gentili A.
Tagliaro F.
Fanali S.
|
Journal of Chromatography A |
10.1016/j.chroma.2019.07.012 |
0 |
Ссылка
© 2019 Elsevier B.V. The chiral separation of baclofen (Bac) was obtained by nano-liquid chromatography tandem mass spectrometry (nano-LC–MS/MS) using a 100 μm I.D. fused silica capillary column packed with silica particles chemically modified with vancomycin. Various experimental parameters, such as composition (buffer concentration, water content, organic modifier) and pH of the mobile phase and sample solvent were investigated for method optimization. In order to increase the sensitivity an on-column focusing procedure was applied. Acceptable separation of Bac enantiomers was obtained in less than 11 min eluting in isocratic mode, with 90:10 MeOH/water (v/v) containing 10 mM ammonium acetate at pH 4.5. These optimized experimental conditions were applied to the analysis of human plasma samples spiked with racemic mixture of Bac. The use of a Buckypaper disc as sorbent membrane allows one to recover both enantiomers with yields ≥ 65%. The method was fully validated, following the identification criteria of the European Commission Decision 2002/657/EC.
Читать
тезис
|
Protein-polymer matrices with embedded carbon nanotubes for tissue engineering: Regularities of formation and features of interaction with cell membranes
|
01.10.2019 |
Slepchenkov M.
Gerasimenko A.
Telyshev D.
Glukhova O.
|
Materials |
10.3390/ma12193083 |
0 |
Ссылка
© 2019 by the authors. This paper reveals the mechanism of nanowelding a branched network of single-walled carbon nanotubes (SWCNTs) used as a framework for the formation of protein-polymer matrices with albumin, collagen, and chitosan. It is shown that the introduction of certain point defects into the structure of SWCNTs (single vacancy, double vacancy, Stone-Wales defect, and a mixed defect) allows us to obtain strong heating in defective regions as compared to ideal SWCNTs. The wavelengths at which absorption reaches 50% are determined. Non-uniform absorption of laser radiation along with inefficient heat removal in defective regions determines the formation of hot spots, in which nanowelding of SWCNTs is observed even at 0.36 nm between contacting surfaces. The regularities of formation of layered protein-polymer matrices and the features of their interaction with cell membrane are revealed. All studies are carried out in silico using high-precision quantum approaches.
Читать
тезис
|
Conjugates of thermally stable phthalocyanine J-type dimers with single-walled carbon nanotubes for enhanced optical limiting applications
|
01.09.2019 |
Savelyev M.
Gerasimenko A.
Podgaetskii V.
Tereshchenko S.
Selishchev S.
Tolbin A.
|
Optics and Laser Technology |
10.1016/j.optlastec.2019.04.036 |
0 |
Ссылка
© 2019 Elsevier Ltd The widespread application of laser devices requires development of new protections against light pulses of high intensity. This problem is relevant because of the danger of hitting the civil aviation pilots with bright and powerful radiation originating from the laser sources which are widely used in the everyday life. Therefore, this work is devoted to continuing our research on a new class of macroheterocyclic compounds – thermally and chemically stable J-type phthalocyanine dimers as potential nonlinear absorbers for optical limiting technology. The dimeric complexes of magnesium (1a) and zinc (1b) were covalently bonded to single-walled carbon nanotubes (SWCNTs) to improve the overall characteristics of the potential optical limiters 2a,b as compared to the previously studied corresponding dyes in solutions. The conjugates obtained were investigated using atomic force microscopy (AFM), as well as Raman and IR spectroscopy to confirm formation of the covalent binding of phthalocyanine macrocycles with the carbon surface. Open-aperture Z-scan and a fixed limiter location experiments have demonstrated low values of the limiting threshold and high degree of attenuation of the input laser radiation with the pulses duration located in the nanosecond range.
Читать
тезис
|
Noninvasive detection of magnetic particles in biological objects
|
13.06.2018 |
Belodedov M.
Ichkitidze L.
Selishchev S.
|
Proceedings - 2018 Ural Symposium on Biomedical Engineering, Radioelectronics and Information Technology, USBEREIT 2018 |
|
0 |
Ссылка
© 2018 IEEE. The possibility of noninvasive detection of magnetic particles in biological objects has been investigated. It has been found that magnetic particles, including magnetite, hematite, and catalytic iron particles in carbon nanotubes, can be detected by ultrasensitive magnetic field sensors with resolutions of 10-8-10-14 T. This research direction is shown to be promising for noninvasive monitoring of organs, implants, prosthesis, and other elements of biological systems.
Читать
тезис
|
Flexible self-powered piezo-supercapacitor system for wearable electronics
|
05.06.2018 |
Gilshteyn E.
Amanbaev D.
Silibin M.
Sysa A.
Kondrashov V.
Anisimov A.
Kallio T.
Nasibulin A.
|
Nanotechnology |
|
3 |
Ссылка
© 2018 IOP Publishing Ltd. The integration of energy harvesting and energy storage in a single device both enables the conversion of ambient energy into electricity and provides a sustainable power source for various electronic devices and systems. On the other hand, mechanical flexibility, coupled with optical transparency of the energy storage devices, is required for many applications, ranging from self-powered rolled-up displays to wearable optoelectronic devices. We integrate a piezoelectric poly(vinylidene-trifluoroethylene) (P(VDF-TrFE)) film into a flexible supercapacitor system to harvest and store the energy. The asymmetric output characteristics of the piezoelectric P(VDF-TrFE) film under mechanical impacts results in effective charging of the supercapacitors. The integrated piezo-supercapacitor exhibits a specific capacitance of 50 F g-1. The open-circuit voltage of the flexible and transparent supercapacitor reached 500 mV within 20 s during the mechanical action. Our hybridized energy harvesting and storage device can be further extended to provide a sustainable power source for various types of sensors integrated into wearable units.
Читать
тезис
|
Vibrational spectroscopy of tissue-engineered structures based on proteins, chitosan, and carbon nanotube conjugates
|
01.01.2018 |
Polokhin A.
Fedorova Y.
Gerasimenko A.
|
Proceedings of SPIE - The International Society for Optical Engineering |
|
1 |
Ссылка
© 2018 SPIE. In this work, tissue-engineered structures based on a matrix of protein conjugates, chitosan and carbon nanotubes were prepared and studied. Bovine serum albumin (BSA), bovine collagen (BCrossed D sign¡) were used. Two types of single-walled carbon nanotubes (SWCNTs) were used to form a strong internal scaffold in a protein-chitosan matrix under the action of laser radiation. Tissue-engineered structures were created by means of layered deposition and laser evaporation of the initial aqueous dispersion from SWCNT, BSA, BC and chitosan succinate. As sources of laser radiation, a continuous diode laser with a wavelength of 810 nm and a pulsed fiber laser with a wavelength of 1064 nm and frequency of 80 kHz were used. Studies of tissue-engineered structures were carried out using vibrational spectroscopy methods (IR and Raman). The changes in the frequencies and intensities of the corresponding absorption bands and Raman lines of the amide group oscillations were analyzed. IR spectra of tissue-engineered structures demonstrated a high degree of binding of organic (protein, chitosan) and inorganic (SWCNT) components. The structure and defectiveness of the carbon nanotube scaffold were investigated in the Raman spectra.
Читать
тезис
|
Layers with the tensoresistive properties and their possible applications in medicine
|
01.01.2018 |
Ichkitidze L.
Gerasimenko A.
Podgaetsky V.
Selishchev S.
|
Materials Physics and Mechanics |
|
2 |
Ссылка
© 2018, Peter the Great St. Petersburg Polytechnic University. Layers of different materials, including nanocomposites, containing carbon nanotubes, with the tensoresistive properties are discussed. The investigated layers are divided into two groups: without (group I) and with carbon nanotubes (group II). A group-I material that is the most suitable for fabrication of a tensoresistor is the elastomer with microchannel, filled with a conductive liquid. In group II, these are the (0.2-10)-μm-thick layers consisting of the carboxymethylcellulose matrix, filled with multiwalled carbon nanotubes (∼5 wt.%). The investigated layers can be used as alternative tensoresistors for medical applications.
Читать
тезис
|
Stimulation of the specific conductivity of the biocompatible nanomaterial layers by laser irradiation
|
01.01.2018 |
Ichkitidze L.
Glukhova O.
Savostyanov G.
Gerasimenko A.
Podgaetsky V.
Selishchev S.
|
Proceedings of SPIE - The International Society for Optical Engineering |
|
0 |
Ссылка
© 2018 SPIE. The conductivity of layers (thickness ∼ 0.5-20 μm) of composite nanomaterials consisting of bovine serum albumin (BSA) with single-walled carbon nanotubes (SWCNTs) has been studied. The BSA/SWCNT composite nanomaterial was prepared according to a route map, some steps of which are: the preparation of an aqueous dispersion based on BSA and SWCNT; preparation of substrates; deposition of BSA/SWCNT dispersion on substrates; application of water paste from SWCNT on substrates; irradiation of layers by lasers when they were in a liquid state; drying of samples; carrying out electrical and temperature measurements. Half of the layer was covered with a light-tight hollow box and the other half of the layer was laser irradiated. The laser irradiation of the layer was carried out for about 20 sec, at which time the layers completely became dry, while the other half of the layer remained in liquid. Conductivity was increased (70 ÷ 650) % by laser irradiation of the layers when they were in the liquid state. Maximum values of specific conductivity for BSA/SWCNT-1 S/m layers, and for layers SWCNT - 70 kS/m. The investigated electrically conductive layers of 99 wt.% BSA/0.3 wt.% SWCNT are promising for medical practice.
Читать
тезис
|
Ingested single-walled carbon nanotubes affect on immunological, hematological and microoecological indices of wistar rats
|
01.01.2018 |
Shipelin V.
Riger N.
Trushina E.
Mustafina O.
Markova Y.
Polyanina A.
Masyutin A.
Chernov A.
Gmoshinsky I.
Khotimchenko S.
|
Gigiena i Sanitariya |
|
0 |
Ссылка
© Izdatel'stvo Meditsina. All rights reserved. Introduction. Single-walled carbon nanotubes (SWCNTs) can create risks to human health when they enter the body by oral route when used in packaging materials, as promising agrochemicals and pesticides. The aim of the study. Evaluation of the subacute oral toxicity of SWCNT in rats. Material and methods. In the 92-days of the experiment, the SWCNTs were administered to rats along with drinking water at doses of 0 (control); 0.01; 0.1; 1.0 and 10 mg/kg body weight (BW) in the groups 1-5, respectively. Hematological indices of blood, apoptosis of hepatocytes, levels of pro- and anti-inflammatory cytokines in blood plasma and their production by cells of the spleen ex vivo, the content of the main and transient components of the intestinal microbiocenosis in the cecum were studied. There were determined hematological blood counts, hepatocyte apoptosis, levels of pro- and anti-inflammatory cytokines in blood plasma and their production by spleen cells ex vivo, content in the cecum of the main and transient components of the intestinal microbiocenosis. Results. At the SWCNT dose of 0.01 mg/kg BW there was a decrease in the number of neutrophils and basophils, an increase in the number of lymphocytes, and a decrease in the number and volume of platelets. At a dose of 0.1 mg/ kg bw there was noted a decrease in the number of cells in the early stage of apoptosis and the total number of cells in apoptosis, as well as a significant decrease in the levels of cytokines IL-10, IL-2, IL-4, IL-13, chemokine MIP-3a, TGF-β isoform 1; at a dose of 1.0 mg/kg IL-12p70, and TGF-β isoforms 1 and 3. TGF- β 2 level was significantly elevated in group 5. The suppressive effect was noted for SWCNTs on the mold flora in intestinal contents at all doses of nanomaterial used, whereas the number of yeasts increased at 1 mg/kg BW. The immunization of rats with ovalbumin had a clear modulating effect on the immunotropic effects of SWCNTs administered at a dose of 0.1 mg/kg BW in a 28-days experiment. Discussion. The mechanisms of the observed changes development are likely to be associated with both systemic anti-inflammatory effects and with a decrease in the effect of SWCNT on the permeability of the intestinal barrier to protein antigens and microbial toxins. Conclusion. SWCNTs exhibit a number of effects in relation to the studied indices that do not demonstrate a monotonic dependence on the dose of nanomaterial, which, apparently, is related to the processes of aggregation of the SWCNT.
Читать
тезис
|
Threshold effect in optical limiters based on conjugates J-type phthalocyanine dimers Zn and Mg with single-walled carbon nanotubes
|
01.01.2018 |
Savelyev M.
Gerasimenko A.
Kuksin A.
Podgaetsky V.
Tolbin A.
Vasilevsky P.
Tereschenko S.
|
Proceedings of SPIE - The International Society for Optical Engineering |
|
0 |
Ссылка
© 2018 SPIE. Laser radiation limiters can be made on the basis of working substances, which have strong nonlinear effects after reaching a certain critical value (threshold limiting). Thus, it becomes possible to obtain a high transmission for a safe beam and a sharply reduced transmission for a hazardous beam. To determine the nonlinear and linear optical properties of these materials there were carried out comprehensive spectroscopic studies, experiments by Z-scan methods with an open aperture and a fixed location of the limiter. Working substances was developed which is suspension of conjugates J-type phthalocyanine dimers Zn or Mg with single-walled carbon nanotubes (SWCNTs) in water. Created conjugates can be used not only for protecting eyes and light-sensitivity elements, but for forming three-dimensional tissueengineered structures. Using conjugates J-type phthalocyanine dimers Zn and Mg with SWCNTs will increase the optical absorption in the wavelength range of laser processing by reducing the thermal effect on other substances in the composition of this structure. The Nd:YAG laser was used as the laser radiation source for generating pulses of 16 ns duration at a wavelength of 532 nm with the linearly polarized laser beam in the horizontal plane and a shape of Gaussian type. The threshold of limiting, linear and nonlinear absorption coefficients were determined by output characteristic, that was obtained by fixed location of the limiter. Created working substances have values of the following order: linear absorption coefficient ∼ 3 cm-1 for layer of 0.2 cm thickness, low limiting threshold ∼ 1 MW·cm-2 and high value of the nonlinear absorption coefficient ∼ 550 cm GW-1. Knowing the nonlinear optical parameters, Z-scan data with an open aperture can be calculated for comparison with experimental data.
Читать
тезис
|
Electrical conductivity of the nanocomposite layers for use in biomedical systems
|
01.01.2018 |
Ichkitidze L.
Gerasimenko A.
Podgaetsky V.
Selishchev S.
Dudin A.
Pavlov A.
|
Materials Physics and Mechanics |
|
4 |
Ссылка
© 2018, Peter the Great St. Petersburg Polytechnic University. Nanocomposite layers consisting of an acrylic paint and single-walled carbon nanotubes (∼1.5 wt.%) have been investigated. The investigated samples had a disk shape with a diameter of 20-30 mm and a thickness of 2-50 μm. After exposure in water for 350 h, the layer mass remained almost invariable (a mass loss of ≤ 1.5%) and the layer samples exhibited high adhesion to glass substrates and a conductivity of ∼ 40 S/m. The layers consisting of the nanotubes and acrylic paint exfoliated from the substrates for ∼1 h. After heat treatment at a temperature of 140 °C, all the layers exhibited a semiconductor-type temperature dependence of the resistance. The prospects of using these layers in various medical products, e.g. implants for wireless energy transmission, have been discussed.
Читать
тезис
|