Репозиторий Университета

© 2020 Ozonation (OZ) is an important advanced oxidation process to purify water and wastewater. Because of the lower solubility and instability of ozone (O3), selective oxidation and dependence on pH value, the industrial applications of OZ have been hindered by the following disadvantages: incomplete removal of pollutants, lower mineralization efficiency and the formation of toxic by-products. Meanwhile, OZ seems to have higher processing costs than other technologies. To improve the treatment efficiency and O3 utilization, several combined processes, such as H2O2/O3, UV/O3, and Cavitation/O3, have been explored, while the combined method of ultrasonication (US) with OZ is a promising treatment technology with a complex physicochemical mechanism. In US alone, the sonolysis of water molecules can produce more powerful unselective oxidant hydroxyl radicals ([rad]OH), and directly cause the sonochemical pyrolysis of volatile pollutants. In US/OZ, US can promote the mass transfer of O3, and also drive the chemical conversion of O3 to enhance the formation of [rad]OH. Various layouts of US/OZ devices and the interactive effects of US/OZ (synergism or antagonism) on the degradation of various organics are illustrated in this review. The main factors, including US frequency, pH value, and radical scavengers, significantly affect the mass transfer and decomposition of O3, the formation of [rad]OH and H2O2, the degradation rates of organics and the removal efficiencies of COD and TOC (mineralization). As a result, US can significantly increase the yield of [rad]OH, thereby improving the degradation efficiency and mineralization of refractory organics. However, US also enhances the decomposition of ozone, thereby reducing the concentration of O3 in water and impairing the efficiency of selective oxidation with O3 molecules.

© 2019 Elsevier B.V. The present study presents an attempt to modify the surface properties of macroporous resins (MRs) in order to improve anthocyanin adsorption and desorption from Pyrus communis var Starkrimson fruit peel extract. A number of MRs were tested to optimise the ultrasonic-assisted adsorption (UAA) conditions; including ultrasonic power (100–400 W), resin-to-extract ratio (1–3 g/50 mL) and temperature (20–40 °C). Similarly, varying ultrasonic-assisted desorption (UAD) conditions were optimised; including ultrasonic power (200–600 W), resin-to-solvent ratio (1–4 g/50 mL), ethanol concentration (60–90% v/v) and temperature (20–40 °C). The Amberlyst 15 (H) cationic resin was found to be superior to the other tested resins. The maximum adsorption capacity (659 µg/g) of cyanidin 3-galactoside (Cy 3-gal) was achieved under the optimised UAA conditions (400 W, 20 °C and 1 g/50 mL), while 616 µg/g of Cy 3-gal was recovered under the optimised UAD conditions (582 W, 1 g/50 mL, 60% and 20 °C). Moreover, titratable-acid and total-sugar contents were found to be significantly lower under UAA than under conventional-assisted adsorption (CAA). ANOVA revealed that process factors had significant effects on the Cy 3-gal purification, as depicted by their linear, quadratic and interactive effects. While anthocyanin adsorption was found to be significantly improved at lower ultrasonic power, higher power promoted the desorption process. Adsorption under optimized UAA conditions followed pseudo second-order kinetics and multilayer adsorption (Freundlich isotherm) onto the Amberlyst 15 (H) resin surface was observed. The particle-size distribution curve and scanning electron microscopic images also revealed higher resin-surface roughness, peeling and the appearance of pores on the surface under ultrasonication. This is the first study to use ultrasonication to modify a cationic exchange resin for the improvement of Cy 3-gal purification from a fruit extract. This study can recommend the use of ultrasonication as a low-cost green technique that can improve macroporous resin characteristics for better purification of compounds from an extract.

© 2019 Elsevier B.V. The present study presents an attempt to modify the surface properties of macroporous resins (MRs) in order to improve anthocyanin adsorption and desorption from Pyrus communis var Starkrimson fruit peel extract. A number of MRs were tested to optimise the ultrasonic-assisted adsorption (UAA) conditions; including ultrasonic power (100–400 W), resin-to-extract ratio (1–3 g/50 mL) and temperature (20–40 °C). Similarly, varying ultrasonic-assisted desorption (UAD) conditions were optimised; including ultrasonic power (200–600 W), resin-to-solvent ratio (1–4 g/50 mL), ethanol concentration (60–90% v/v) and temperature (20–40 °C). The Amberlyst 15 (H) cationic resin was found to be superior to the other tested resins. The maximum adsorption capacity (659 µg/g) of cyanidin 3-galactoside (Cy 3-gal) was achieved under the optimised UAA conditions (400 W, 20 °C and 1 g/50 mL), while 616 µg/g of Cy 3-gal was recovered under the optimised UAD conditions (582 W, 1 g/50 mL, 60% and 20 °C). Moreover, titratable-acid and total-sugar contents were found to be significantly lower under UAA than under conventional-assisted adsorption (CAA). ANOVA revealed that process factors had significant effects on the Cy 3-gal purification, as depicted by their linear, quadratic and interactive effects. While anthocyanin adsorption was found to be significantly improved at lower ultrasonic power, higher power promoted the desorption process. Adsorption under optimized UAA conditions followed pseudo second-order kinetics and multilayer adsorption (Freundlich isotherm) onto the Amberlyst 15 (H) resin surface was observed. The particle-size distribution curve and scanning electron microscopic images also revealed higher resin-surface roughness, peeling and the appearance of pores on the surface under ultrasonication. This is the first study to use ultrasonication to modify a cationic exchange resin for the improvement of Cy 3-gal purification from a fruit extract. This study can recommend the use of ultrasonication as a low-cost green technique that can improve macroporous resin characteristics for better purification of compounds from an extract.